Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.15.1. Check of the directing plug of the valve
2.2.15.2. Measurement of length of the valve
2.2.15.3. Measurement of diameter of a core of the valve
2.2.15.4. Measurement of internal diameter of the directing plug of the valve
2.2.15.5. Measurement of height of a vystupaniye of the directing plug of the valve
2.2.15.6. Replacement of the directing plug of the valve
2.2.15.7. A press fitting of the directing plug of the valve
2.2.15.8. Check and repair of a saddle of the valve
2.2.15.9. Check of a klapanny spring
2.2.15.10. Cam-shaft check
2.2.15.11. Measurement of diameter of a neck of a cam-shaft
2.2.15.12. Measurement of a radial gap of a neck of a cam-shaft
2.2.15.13. Measurement of an axial gap of a neck of a cam-shaft
2.2.15.14. Check of a pusher of the valve
2.2.15.15. Check of the block of cylinders
2.2.15.16. Check of the valve of a maslorazbryzgivayushchy nozzle
2.2.15.17. Check of a cranked shaft
2.2.15.18. Measurement of size of palpation of a cranked shaft
2.2.15.19. Measurement of diameters of necks of a cranked shaft
2.2.15.20. Measurement of a radial gap in radical bearings of a cranked shaft
2.2.15.21. Check of a lateral gap of a rod
2.2.15.22. Measurement of a radial gap of a rod
2.2.15.23. Check of bolts
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







2-2-15-10-proverka-raspredvala.html

2.2.15.10. Cam-shaft check

Establish necks No. 1 and cam-shaft No. 5 on prisms.

Fig. 2.152. Measurement of palpation of a cam-shaft


Measure cam-shaft palpation (fig. 2.152).
If palpation does not correspond to norm, replace a cam-shaft.
Maximum palpation: 0,03 mm.

Fig. 2.153. Measurement of height of a contour of a cam


Measure height of a contour of a cam in two points, as is shown in drawing 2.153.
If the height does not correspond to norm, replace a cam-shaft.
Neck No. 1.
Standard height of a cam-shaft of L8:
Admission – 40,79 mm;
Release – 41,08 mm.
Cam-shaft of LF, L3:
Admission – 42,12 mm;
Release – 41,08 mm.
With the mechanism of change of phases of a gazoraspredeleniye:
Admission – 42,44 mm;
Release – 41,18 mm.
Neck No. 5
Standard height of a cam-shaft of L8:
Admission – 40,692 mm;
Release – 40,982 mm.
Cam-shaft of LF, L3:
Admission – 42,022 mm;
Release – 40,982 mm.
With the mechanism of change of phases of a gazoraspredeleniye:
Admission – 42,342 mm;
Release – 41,082 mm.

«previous page
2.2.15.9. Check of a klapanny spring
following page»
2.2.15.11. Measurement of diameter of a neck of a cam-shaft