Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







2-2-8-proverka-ispolnitelnogo-mekhanizma-izmeneniya-faz-gazoraspredeleniya-l3.html

2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)

ATTENTION
The executive mechanism of change of phases of a gazoraspredeleniye is precision knot and to dismantling is not subject.

Disconnect a negative wire of the storage battery.
Remove an opening plate under a stopper.
Remove a high-voltage wire.
Remove the socket of the operating oil valve.
Remove a ventilation hose.
Uncover heads of the block of cylinders.

Fig. 2.99. Combination of a groove of a rotor with camber of a cover of the mechanism of change of phases of a gazoraspredeleniye


Be convinced that the groove of a rotor and camber of a cover of the executive mechanism of change of phases of a gazoraspredeleniye are combined (fig. 2.99).
If the groove and camber are not combined, turn a cranked shaft clockwise on two turns. Check groove and camber combination. If the groove and camber again do not coincide, replace the executive mechanism of change of phases of a gazoraspredeleniye. If at rotation of a cranked shaft knock of the executive mechanism of change of phases of a gazoraspredeleniye each time when the cam passes the provision of complete opening of the valve is audible, it means that the executive mechanism is not fixed. Replace the executive mechanism.
Establish a cover of a head of the block of cylinders (see. «Removal and installation of a cover of a head of the block of cylinders»).
Establish a ventilating hose.
Connect the socket of the operating oil valve.

Fig. 2.100. Fastening of high-voltage wires: 1–clip; 2–rubber plug; 3–wire winding; 4–union tip; 5–installation sites of rubber plugs; 6–installation sites of clips


Connect a high-voltage wire (fig. 2.100).
Establish spark plugs.
Establish an opening plate under a stopper.

«previous page
2.2.7.5. Support No. 1 installation
following page»
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)