Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.1.1. Mechanical part of engines
2.1.1.1. Cover of a head of the block of cylinders
2.1.1.2. Head of the block of cylinders
2.1.1.3. Laying of a head of the block of cylinders
2.1.1.4. Block of cylinders
2.1.1.5. Cranked shaft and radical bearing
2.1.1.6. Balancing block
2.1.1.7. Principle of operation of the balancing block
2.1.1.8. Damper of krutilny fluctuations of a cranked shaft
2.1.1.9. Forward cover of the engine
2.1.1.10. Piston
2.1.1.11. Piston rings and piston finger
2.1.1.12. Rod and shatunny bearing
2.1.1.13. The Klapanny mechanism – general information
2.1.1.14. Camshaft
2.1.1.15. Camshaft asterisk
2.1.1.16. Asterisk of a cranked shaft
2.1.1.17. Chain of a drive of the mechanism of a gazoraspredeleniye
2.1.1.18. Natyazhitel of a chain of a drive of the mechanism of a gazoraspredeleniye
2.1.1.19. The valve, a klapanny spring, the maslootrazhatelny cap, the directing plug of the valve
2.1.1.20. Valve pusher
2.1.2. Mechanism of change of phases of a gazoraspredeleniye
2.1.3. Greasing system
2.1.4. Cooling system
2.1.5. Fuel system
2.1.6. System of production of the fulfilled gases and system of decrease in toxicity
2.1.7. Electric equipment of engines
2.2. Mechanical part of engines
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 






Бти бюро технической инвентаризации киева

2-1-1-4-blok-cilindrov.html

2.1.1.4. Block of cylinders

Technological feature of the new block of cylinders is that it is cast from an aluminum alloy with the pig-iron sleeves of cylinders established in the case. It improves heat removal and reduces its weight. Sleeves of cylinders – thin-walled, thus, boring is not possible. Besides, as it was already told, the block of cylinders is supplied with a long skirt of the piston and the integrated cover of radical bearings. The water shirt of the block of cylinders – the closed type that increases a zheskost and promotes vibration and noise reduction. The cover of an oil separator of the block of cylinders is located on the opposite side of an air inlet. The valve of ventilation of a case and an oil separator with an adapter for installation of the valve of ventilation improve efficiency of ventilation of karterny gases.

Fig. 2.6. Block of cylinders: 1–oil separator cover; 2–PCV valve; 3–cover of the radical bearing; 4–flange of a cover of an oil separator; 5–block of cylinders


On the new block of cylinders adjusting shponka of bearings of radical necks are not applied. Bolts of fastening of a head of cylinders have the inhaling moment in a plasticity zone, the inhaling is carried out in five receptions. It provides stability of an axis of a bolt at an inhaling (fig. 2.6).

Fig. 2.7. A technological opening for detection of position VMT of the first cylinder: 1–block of cylinders; 2–cylinder No. 1; 3–technological opening; 4–special adaptation; 5–VMT of the first cylinder; 6–piston of the first cylinder; 7–counterbalance of a cranked shaft


The technological opening for installation of the special adaptation used for detection of position VMT of the first cylinder, settles down on the right side of the block of cylinders. Situation VMT is determined by a contact of edge of the special adaptation of the balance weight of the first cylinder (fig. 2.7).

«previous page
2.1.1.3. Laying of a head of the block of cylinders
following page»
2.1.1.5. Cranked shaft and radical bearing