Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.7.1. Support No. 1 removal
2.2.7.2. Removal of an arm of a support of the engine No. 4 and engine No. 4 support
2.2.7.3. Installation of an arm of fastening of the engine No. 3
2.2.7.4. Installation of an arm of a support of the engine No. 4 and engine No. 4 support
2.2.7.5. Support No. 1 installation
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







2-2-7-2-snyatie-kronshtejjna-opory-dvigatelya-n4-i-opory-dvigatelya-n4.html

2.2.7.2. Removal of an arm of a support of the engine No. 4 and engine No. 4 support

Fig. 2.92. Motor jack


Fix the engine and a transmission in the block with the main transfer, using a motor jack and an extra (fig. 2.92).

Fig. 2.89. Components of fastening of the power unit on the car: 1–engine No. 1 support; 2–arm of a support of the engine No. 1; 3–arm of a support of the engine No. 4 and engine No. 4 support; 4–the tire of connection of the engine with "mass" of a body; 5–arm of fastening of the engine No. 3; 6–the engine, a transmission in the block with the main transfer


Remove the special adaptation (see fig. 2.89).

Fig. 2.93. Engine and transmission fixing on the lift


Fix the engine and a transmission in the block with the main transfer, using the lift (fig. 2.93).

Fig. 2.94. Arm of a support of the engine No. 4 and support of No. 4 engines assembled


Remove an arm of a support of the engine No. 4 and a support of No. 4 engines assembled (fig. 2.94).

«previous page
2.2.7.1. Support No. 1 removal
following page»
2.2.7.3. Installation of an arm of fastening of the engine No. 3