Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.1.1. A car design with a body "sedan"
8.1.2. A car design with a body "hatch-back"
8.1.3. Body framework
8.1.4. Hinged and decorative components of a body
8.1.5. Doors
8.1.6. Window regulators
8.1.7. Dismantling and trunk lid assembly
8.1.8. Removal and installation of a front bumper
8.1.9. Dismantling and assembly of a front bumper
8.1.10. Removal and installation of a rear bumper
8.1.11. Removal and installation of a back slip
8.1.12. Removal and installation of a back spoiler
8.1.13. External rear-view mirrors
8.1.14. Removal and installation of an external mirror with the electric drive
8.1.15. Dismantling and assembly of an external mirror with the electric drive
8.1.16. Heater of back glass
8.1.17. The hatch on a roof
8.1.17.1. Removal and installation of the deflector of the hatch
8.1.17.2. Removal and installation of glass of the hatch
8.1.17.3. Hatch adjustment
8.1.18. Seat belts
8.1.19. Seats
8.2. Conditioner and heater
 






8-1-17-lyuk-na-kryshe.html

8.1.17. The hatch on a roof





ATTENTION
Do not allow under way the car to rise or put out to passengers in the hatch of a part of a body or any subjects. Before closing the ventilating hatch, be convinced that the aperture of the hatch is free and anybody from passengers cannot jam a part of the body. Imprudent closing of the ventilating hatch can represent danger.

NOTE
After a wash of the car or after a rain remove water from a cover of the ventilating hatch before opening it. It is necessary to prevent water hit in salon which can cause corrosion of a body and damage of an upholstery of a ceiling.

Automatically completely to raise a cover, press the back region of a key of the TILT switch (Lifting lowering). If it is required to stop a cover in intermediate situation, press any region of a key of the switch of lifting lowering or a key of the switch of longitudinal moving of a cover of the hatch. To cover a cover and to bring it into demanded situation, press a first line of any of two SLIDE or TILT keys.
Automatically completely to shift a cover, press the back region of the SLIDE key. If it is required to stop a cover in intermediate situation, press any region the TILT keys (Lifting lowering) or the SLIDE keys (Longitudinal moving of a cover of the hatch). To cover a cover and to bring it into demanded situation, press a first line of any of two SLIDE or TILT keys.

The hatch on a roof
Fig. 8.55. The hatch on a roof: 1–deflector; 2–hatch switch; 3–hatch electric motor; 4–hatch block


Assembly diagram of system of the electrohatch
Fig. 8.56. Assembly diagram of system of the electrohatch: 1–hatch switch; 2–hatch relay; 3–chain of management of the engine; 4–scheme of detection of a current of blocking of the engine; 5–relay; 6–trailer switch No. 1; 7–trailer switch No. 2; 8–trailer switch No. 3; 9–hatch electric motor; 10-openly; 11-it is closed; 12-inclination down; 13-inclination up; 14-opening/inclination down; 15-closing/inclination up



«previous page
8.1.16. Heater of back glass
following page»
8.1.17.1. Removal and installation of the deflector of the hatch