Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.4.1. Check procedure
2.2.4.2. Replacement of a driving belt
2.2.4.3. Check of an automatic natyazhitel of a driving belt
2.2.4.4. Check of thermal gaps in the mechanism of a drive of valves
2.2.4.5. Adjustment of thermal gaps in the mechanism of a drive of valves
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







2-2-4-4-proverka-teplovykh-zazorov-v-mekhanizme-privoda-klapanov.html

2.2.4.4. Check of thermal gaps in the mechanism of a drive of valves

Disconnect a negative wire of the storage battery.
Remove the right wheel.
Remove the right mudguard.
Turn out spark plugs.
Disconnect a high-voltage wire.
Disconnect the socket of the operating oil valve (OCV).
Remove a ventilation hose.
Uncover heads of the block of cylinders. Make sure that the engine cold.
Measure a klapanny gap.
For measurement of a klapanny gap turn a cranked shaft clockwise so that the piston No. 1 was established in VMT of a step of compression.

Fig. 2.77. Order of measurement of klapanny gaps


By means of special щупа measure a klapanny gap in a point And (fig. 2.77).
Write down the measured values to choose the corresponding pushers of the valve if their replacement further is required.
Turn a cranked shaft on 360 ° clockwise so that the piston No. 4 was established in VMT of a step of compression.
The same as in the first case, measure a klapanny gap in B point (see fig. 2.77).
Standard gap (on the cold engine):
admission – 0,22–0,28 mm;
release – 0,27–0,33 mm.
If klapanny gaps does not correspond to norm, adjust them, or, in case of impossibility of adjustment, replace pushers of valves new.
Establish all removed details into place as it should be, the return to removal.

«previous page
2.2.4.3. Check of an automatic natyazhitel of a driving belt
following page»
2.2.4.5. Adjustment of thermal gaps in the mechanism of a drive of valves