Mazda 6 since 2002
1. Operation and car maintenance
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.2.1. Engines of the L8 and LF models
2.2.2. Verification of the contents WITH / SN in the fulfilled gases
2.2.3. Compression measurement in engine cylinders
2.2.4. Check of a belt of a drive of auxiliary units
2.2.5. General information and safety measures at removal of the power unit
2.2.6. Hermetic removal
2.2.7. Removal and installation of the power unit
2.2.8. Check of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.9. Removal and installation of the executive mechanism of change of phases of a gazoraspredeleniye (L3)
2.2.10. Chain of a drive of the mechanism of a gazoraspredeleniye
2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
2.2.12. Check of the operating oil valve (OCV) (L3)
2.2.13. Check of operation of the zolotnikovy valve (OCV) (L3)
2.2.14. The general repair operations on the power unit
2.2.15. Check of a head of the block of cylinders
2.2.16. Assembly of the block of cylinders (beginning)
2.2.17. Assembly of the block of cylinders (termination)
2.2.18. Assembly of a head of the block of cylinders
2.2.18.1. Installation of a maslootrazhatelny cap
2.2.18.2. Installation of a head of the block of cylinders
2.2.18.3. Installation of cam-shafts
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 







2-2-18-3-ustanovka-raspredvalov.html

2.2.18.3. Installation of cam-shafts

Establish cam-shafts, thus the piston of the cylinder No. 1 it should be established in the provision VMT of a step of compression.

Fig. 2.187. Order of a tightening of bolts of fastening of covers of bearings of cam-shafts


Tighten bolts of fastening of a cover of the bearing of a cam-shaft in two steps (fig. 2.187).
Tighten to 5,0–9,0 N · m.
Tighten to 14.0–17,0 N · m.

Instructions on assembly of an asterisk of a camshaft, the executive mechanism of change of phases of a gazoraspredeleniye (L3 with the mechanism of change of phases of a gazoraspredeleniye).
Bolt of an asterisk of a camshaft or the executive mechanism of change of phases of a gazoraspredeleniye (L3 with the mechanism of change of phases of a gazoraspredeleniye) is temporary, before installation of a chain of a drive of the mechanism of a gazoraspredeleniye, is rolled manually.

Fig. 2.188. Tightening of a bolt of fastening of an asterisk of a cam-shaft (the ordinary engine) and executive mechanism of change of phases of a gazoraspredeleniye


The connecting bolt of an asterisk of a camshaft or the executive mechanism of change of phases of a gazoraspredeleniye (with the mechanism of change of phases of a gazoraspredeleniye) after installation of a chain of a drive of the mechanism of a gazoraspredeleniye is established to L3 on glue (fig. 2.188).
Inhaling moment: 69–75 N · m.

«previous page
2.2.18.2. Installation of a head of the block of cylinders
following page»
2.2.19. Assembly of a drive of the mechanism of a gazoraspredeleniye